Search results for "readout [electronics]"
showing 10 items of 18 documents
Update on the TowerJazz CMOS DMAPS development for the ATLAS ITk
2019
The upgrade of the ATLAS tracking detector for the High-Luminosity Large Hadron Collider at CERN requires the development of novel radiation hard silicon sensor technologies. For the de- velopment of depleted CMOS sensors for ATLAS we combined small electrodes with minimal capacitance and advanced processing for fully depleted active sensor volume to achieve radiation hard CMOS sensors in line with ATLAS ITk specifications. Based on initial studies on the prototype sensor “TowerJazz Investigator” we have now developed, produced and tested a first full-size depleted CMOS sensor based on the 180nm TowerJazz imag- ing process, the so-called “MALTA” sensor. The sensor combines special low-noise…
The sROD demonstrator for the ATLAS Tile Calorimeter Upgrade
2012
This work presents the early design of the super Read-Out Driver (sROD) demonstrator board for the Tile Calorimeter Demonstrator project. This project aims to test the new readout electronics architecture for the Phase 2 Upgrade of the ATLAS Tile Calorimeter, replacing the front-end electronics of one complete drawer with the new electronics during the Long Shutdown 2013, in order to evaluate its performance. The sROD demonstrator board will receive and process data from 48 channels. Moreover the sROD demonstrator board will send preprocessed data to the present trigger system, and will transmit trigger control and timing information (TTC) and Detector Control System (DCS) commands to the f…
Large area strip edgeless detectors fabricated by plasma etching process
2007
This work presents the last results from large area edgeless detector, fabricated by Plasma Etching Process to reduce the conventional width of the terminating structure of position sensitive detectors to the detector rim.. A current terminating ring is used to decouple the electrical behavior of the surface from the sensitive volume within a few tens of micrometers. The detectors have been illuminated using an infrared laser and their surface scanned in order to understand their collection behavior at the cut edge. The detectors have very high efficiency up to the insensitive area which is located about 60 mum from the detector edge.
Radiation hard monolithic CMOS sensors with small electrodes for High Luminosity LHC
2019
Abstract The upgrade of the tracking detectors for the High Luminosity-LHC (HL-LHC) requires the development of novel radiation hard silicon sensors. The development of Depleted Monolithic Active Pixel Sensors targets the replacement of hybrid pixel detectors with radiation hard monolithic CMOS sensors. We designed, manufactured and tested radiation hard monolithic CMOS sensors in the TowerJazz 180 nm CMOS imaging technology with small electrodes pixel designs. These designs can achieve pixel pitches well below current hybrid pixel sensors (typically 50 × 50 μ m ) for improved spatial resolution. Monolithic sensors in our design allow to reduce multiple scattering by thinning to a total si…
Studies for low mass, large area monolithic silicon pixel detector modules using the MALTA CMOS pixel chip
2021
Abstract The MALTA monolithic silicon pixel sensors have been used to study dicing and thinning of monolithic silicon pixel detectors for large area and low mass modules. Dicing as close as possible to the active circuitry will allow to build modules with very narrow inactive regions between the sensors. Inactive edge regions of less than 5 μ m to the electronic circuitry could be achieved for 100 μ m thick sensors. The MALTA chip (Cardella et al., 2019) also offers the possibility to transfer data and power directly from chip to chip. Tests have been carried out connecting two MALTA chips directly using ultrasonic wedge wire bonding. Results from lab tests show that the data accumulated in…
Expansion cone for the 3-inch PMTs of the KM3NeT optical modules
2013
[EN] Detection of high-energy neutrinos from distant astrophysical sources will open a new window on the Universe. The detection principle exploits the measurement of Cherenkov light emitted by charged particles resulting from neutrino interactions in the matter containing the telescope. A novel multi-PMT digital optical module (DOM) was developed to contain 31 3-inch photomultiplier tubes (PMTs). In order to maximize the detector sensitivity, each PMT will be surrounded by an expansion cone which collects photons that would otherwise miss the photocathode. Results for various angles of incidence with respect to the PMT surface indicate an increase in collection efficiency by 30% on average…
The upgrade of the ALICE TPC with GEMs and continuous readout
2020
Journal of Instrumentation 16(03), P03022 (2021). doi:10.1088/1748-0221/16/03/P03022
MALTA: an asynchronous readout CMOS monolithic pixel detector for the ATLAS High-Luminosity upgrade
2019
The ATLAS collaboration is currently investigating CMOS monolithic pixel sensors for the outermost layer of the upgrade of its Inner Tracker (ITk). For this application, two large scale prototypes featuring small collection electrode have been produced in a radiation-hard process modification of a standard 0.18 μm CMOS imaging technology: the MALTA, with a novel asynchronous readout, and the TJ MONOPIX, based on the well established "column-drain" architecture. The MALTA chip is the first full-scale prototype suitable for the development of a monolithic module for the ITk. It features a fast and low-power front-end, an architecture designed to cope with an hit-rate up to 2 MHz/mm2 without c…
The fast readout system for the MAPMTs of COMPASS RICH-1
2007
A fast readout system for the upgrade of the COMPASS RICH detector has been developed and successfully used for data taking in 2006 and 2007. The new readout system for the multi-anode PMTs in the central part of the photon detector of the RICH is based on the high-sensitivity MAD4 preamplifier-discriminator and the dead-time free F1-TDC chip characterized by high-resolution. The readout electronics has been designed taking into account the high photon flux in the central part of the detector and the requirement to run at high trigger rates of up to 100 kHz with negligible dead-time. The system is designed as a very compact setup and is mounted directly behind the multi-anode photomultiplie…
A low-noise and fast pre-amplifier and readout system for SiPMs
2015
Abstract To operate silicon photomultipliers (SiPMs) in a demanding environment with large temperature gradients, different amplifier concepts were characterized by analyzing SiPM pulse-shapes and charge distributions. A fully differential 4-wire SiPM pre-amplifier with separated tracks for the bias voltage and with good common-mode noise suppression was developed and successfully tested. To achieve highest single-pixel resolutions an online after-pulse and pile-up suppression was realized with fast readout electronics based on digital filters.